Search

Search results
1 - 20 / 43

1021 - Ecoven View O&U sheet
Description

-New adjustment block/oven support: Independent setting of neck cooling shield for more stability

-Ecoven module for lamps cooling: The Super Cobra is replaced by a fan dedicated to each module

-Heating modules: Only 8 IR lamps, more efficient lamps, ceramic wall and top reflector

-Ceramic oven top reflector, adjustable in height to fit all preform lengths

-Wiring: Pre-wired cabinet added to supply power to the fans

-New automation and process: Updated main electrical cabinet (power supply, new functionalities and readjustment of all process sheets)

Benefits

-20% to 45% less electrical consumption

-Fewer lamps for 11% less installed power

-Sharper heating: Sharp zoning on preform surface and optimized under-neck stretching

-Easier to maintain: Heating module can be serviced on the bench while the machine runs with a spare module

-Ceramics are self-cleaning via pyrolysis effect

 

Yearly avoided Green House Gas emissions - Up to 333t CO2 (*)

 

 

(*) Result for an SBO 20  producing 1l bottle

     a. 30000 bottle/h speed rate

     b. 6000h production time / year

Key message
Reduce your electricity consumption by 20% to 45% (Yearly avoided Green House Gas emissions - Up to 333t CO2 (*))
Machine application

All Universal except Predis C3 & C5.

1031 - Oven heat recovery system View O&U sheet
Description

The oven heat recovery system components:

-New air inlet module (1, 2)

-One bottom ventilation module including a fan (3, 4, 5)

-One top ventilation module (6,7)

Benefits

-Secure blowing process stability

-Avoid bottle quality issues due to ambient temperature variation

Key message
Increase your equipment efficiency and secure product quality
Machine application

UNIVERSAL blowers

1006 - Predis™ C3 View O&U sheet
Description

The Predis™ system is located in the oven entrance.

-First, the hydrogen peroxide (H2O2 employed as sterilized agent) is deposited onto the internal wall of each preform.

-Performs are then heated in the oven until they reach a temperature of up to 100°C which guarantees activation of the H2O2.

-In a constant controlled atmosphere, the system ensures reduction in microorganisms between the preform and the filled-capped bottle.

Benefits

-Self protection due to H2O2 exhaust after activation and blowing phases

-Economical: Low consumption of chemical & energies

-Low maintenance and labor costs

-Ecological: Low power; no water consumption; no effluents; compact system

-Packaging: Possible light weighting; total freedom of shape

Key message
Dry preform decontamination
Machine application

PM MM GM Universal

102 - Quick Change infeel wheel View O&U sheet
Description

Replacement of old generation in-feed (blocks) by new generation (16 notched star wheel).

Benefits

Gives better results in terms of preform stabilisation (in case of light preform) at oven entrance.

Contribute to reduce change over time due to Quick/Change equipment.

Key message
Reliable preform loading
Machine application

Blowers S1 - SBO 4/4 - SBO 4/6 - SBO 6/6 - SBO 6/10 - SBO 10/10 - SBO 10/14 - SBO 16

1024 - PCC version V3.09 View O&U sheet
Description

In the event of an equipment failure, there are two options for maintenance of production:

-Either deactivation of the non-functional box with a corresponding adjustment of the heating profile to offset the loss of heating capacity.

-Or replacement of the box with an equivalent: an Olicorps box can thus be replaced with a Siemens box without the need for any change in automated procedures.

Comment: box selection is possible only if the box is activated and if no lamp is being used on the oven concerned.

Benefits

- Continuation of production despite the failure of one of the heating boxes.

- Configuration, activation and deactivation of each heating box independently in a new screen page

-Because cyber security is a must for industrial control systems, you can move to the W10 HMI version!

 Ask more about our product

 

1051_HMI migration to Windows 10

Key message
Maintain your production in the event of a heating box failure
Machine application

Blowers Universal

1027 - Gaz shocks on Ecoven View O&U sheet
Description

-Depending on the size of the oven, one or more gaz shock can be placed under each rack. These cylinders are calibrated according to the force to be produced, they are attached at the bottom,  to the oven frame.

-A locking latch system keeps the racks in the down position. Indeed, without this lock, whenever a heating module is extracted, the rack would tend to rise under the thrust of the cylinders.

-Applicable only on ECOVEN

Benefits

•Damping of the downward movement during opening of the oven racks.

•When closing the racks, the gas shocks assist the operator in his movement, reducing the needed effort.

Key message
Increase operator safety
Machine application

Universal with ECOVEN

1053 - 5s Tool Box View O&U sheet
Description
  • A cabinet for storing the SIDEL specific tools, to be mounted on the preform feeder gangways.
  • Tools are sorted by items to be maintained: transfer arms, oven, PUPM, 40mm nozzle cylinders (upgraded snap ring free).
  • 4 individual removable trays.
  • Workshop trolley available upon request
Benefits

Reduce time lost in looking for right tools

A 5S systematic arrangement for an organized maintenance activity

Key message
Sort - Set in Order - Shine - Standardize - Sustain
Machine application

Blower Series2 – Universal - Matrix

113 - Reinforced oven ventilation View O&U sheet
Description

Replacement of old generation oven ventilation box by new generation (ventilation through reflectors) including electronic driven ventilator (adjustable speed).

Benefits

- Improve the penetration of the infra red.

- Give better results in term of heating power particularly in case of high speed, light preforms or special process.

- Recommended to secure rPET bottle production for:

       a. neck protection

       b. process robustness

       c.  ensure optimal material distribution

Key message
Improve preform skin cooling
Machine application

Blowers S1- SBO 4/4 - SBO 6/6 - SBO 10/10 - SBO 16 - SBO 24/26

117 - Reinforced neck ventilation at oven end View O&U sheet
Description

Adaptation of ventilation system on necks at oven end, including additional ventilators.

Benefits

- Give better results in term of neck protection particularly in oven turn at the end.

- Recommended to secure rPET bottle production for:

       a. neck protection

       b. process robustness

  

Key message
Cool down the preforms necks
Machine application

Blowers S1- SBO 4/4 - SBO 6/6 - SBO 10/10 - SBO 16 - SBO 24/26

118 - Angle ovens View O&U sheet
Description

Adaptation of a 2 IR lamps module (zone 1&2) at oven end.

Benefits

Contribute to improve heating power under neck ring in order to easiate streching under neck.

Key message
Improve heating on zone 1&2
Machine application

Blowers S1- SBO 4/4 - SBO 6/6 - SBO 10/10 - SBO 16 - SBO 24/26

119 - 15 mm pitch oven racks for IR lamps View O&U sheet
Description

Modifications in order to reduce lamp pitch from 19mm to 15 mm.

Benefits

- Allow to adjust heating profile to preform dimensions.

- Allow to concentrate the heating power on smaller area in case of blowing short and light preforms (8 heating zones).

- Increase heating power by 25% when long and heavy preforms are blown (in this case, two extra zones are added: z9 & z10)

Key message
Improve heating
Machine application

Blowers S1- SBO 4/4 - SBO 6/6 - SBO 10/10 - SBO 16 - SBO 24/26

120 - Additional heating zones 9 & 10 View O&U sheet
Description

Adaptation of 2 additional heating zone ( 9 & 10) if not existing originally.

Benefits

Contribute to increase heating power, in case of long preform, by increasing amount of lamps inside the oven.

Key message
Extra heating power
Machine application

Blowers S1- SBO 4/4 - SBO 6/6 - SBO 10/10 - SBO 16 - SBO 24/26

2031 - Additional IR camera at the oven exit View O&U sheet
Description

-A second camera is installed at the oven exit

-All anomalies are indicated to the PLC

Benefits

Control of preform temperature at the exit of the oven

Key message
Secure blowing process
Machine application

Blowers MATRIX

2044 - Neck Finish Air Cooling View O&U sheet
Description
  • A vortex tube produces refrigerated air from high pressure air skid
  • Low temperature air is blown on the neck finishes trough perforated tubes, with adjustable positioning against the water cooling shields, right below the oven modules
Benefits
  • Maintain neck finish at a suitable temperature
  • Prevent neck finish deformation during blowing
  • Recommended for r-Pet production
Key message
Neck always at the right temperature
Machine application

Universal, Matrix

2055 - Oven air cooling system View O&U sheet
Description

The oven air cooling system components:

-an air/water thermic exchanger (radiator)  in front of the oven ventilation

-a 3 way valve allowing the water flow regulation through bypass (controlled by a temperature probe)

-the temperature is adjusted from the HMI

Benefits

-Increase process flexibility (widen process window)

-Avoid oven overheating

-Secure bottle neck quality

Key message
Increase your equipment efficiency and secure product quality
Machine application

MATRIX blowers

2057 - LINMOT for Matrix SBO View O&U sheet
Description

-Linear motor replacing the cambox

-No oil lubrication

-Simpler than the current solution

-Disconnected from the machine drive chain

-No more need to move the oven to replace the component

Benefits

-Reduce maintenance costs

-Increase equipment hygeen level

-Secure operator safety in case of intervention

-No more torque variation due to unloading

-More accurate preform transfer

-A single reference for the whole range of blower  (Spare parts)

Key message
Reduce maintenance costs and secure product quality
Machine application

Blower Matrix PH

2086 - Oriented infrared lamps View O&U sheet
Description
  • On each heating module, a pair of individual lamp holders are inserted into the racks,.
  • IR beam of the upper lamp, can be directed according to the most relevant angle
  • This heating profile customization is fully reversible.
  • Suitable for all types of oven
Benefits
  • Precise heating of  the preform end area.
  • Allow a better control of the material distribution.
  • In some cases, can facilitate the production of very “technical” bottles
Key message
Best control of preform material distribution
Machine application

SBO Series 1, 2, Universal, Matrix

2087 - Dual entry oven ventilation View O&U sheet
Description
  • An additional ventilation box to be installed opposite to the existing single ventilation box.
  • Air is sucked from both sides of the oven.
Benefits
  • Larger flow of air for preform ventilation.
  • Enlarge the process window for rPET applications.
  • In some cases, it can ease the production of very technical bottles
Key message
Widen the process window for rPET applications
Machine application

Blower Matrix

503 - Preferential heating View O&U sheet
Description

According to the production set-up, the oven heating modules can be equipped with reflectors. Each comb reflector is fitted with five independently adjustable vents.

The rapid off-load system is fitted with a rotary cam which raises and lowers a shaft which in turn raises the ejector rod.

The arm-head is oriented by the cam follower and the grip opening/closing movements are controlled by a second cam follower ensuring that the preform does not move during transfer.

The 4-stage cylinder nozzle holds the preform in the mold as it goes down (1st stage) preventing the preform from slipping from the grips as they open.The second down-stage will only take place once the grips have retracted.

Benefits

The preferential heating option allows the production of flat-sided and asymmetrical containers.

Depending on the production set-up and the item being manufactured, this option may be associated with the supplementary option: neck indexing in the oven

Key message
Production of flat-sided ans aymetrical containers
Machine application

Blowers S2 - PM with liear oven only, MM, GM

506 - Preform de-dusting View O&U sheet
Description

-The dedust wheel comprises 30 injectors which blow compressed (at 2 bars) filtered air into the preforms

-Independently of the air supply for the machine air cylinders, the compressed air system provides a high level of filtration using a prefilter, a filter and an total filter. It also brings down air pressure from 7 bars to 2 bars

-The air suction hood comprises a turbine fan in a sealed housing, a particle filter and two baffles to channel air suction flow

-Drive for the rotation of the feed wheel, the dedust wheel and the transfer wheel is provided by a belt itself driven by the oven transmission shaft

Benefits

-The system is eliminating any residual particles from preforms (more than 97%)

-Enables preforms to be cleaned internally before blowing

Key message
Increase hygiene level
Machine application

Blower S2 PM MM GM