Search

The current solution results in a complete dismantling of the fork to enable changeovers.

The new solution allows neck changeover by changing the neck support of the fork without removing the support.

-The current solution with traditional valves may limit the filler speed due to foaming

-The new solution proposes filling valves with a swirler device in order to reduce product foaming during the filling phase

-The gripper thickness is increased from 3 to 5 mm

-New design of the gripping zone

-New design of plastic bushes

-The new trolley is fitted with a quick-change system which enables fast and easy substitution of the roller.

-The new trolley is fitted with a stiffening system which considerably reduces the deformation by the flexing and twisting during the filling step.

-The anti-rotation system reduces malfunctions and premature wear 

One of the current filling valve membrane functionalities is to close the valve, so the wear and tear level of this membrane impacts on filling level reliability

The new solution proposes:

-Filling valves with external spring

-Vent tube with ball (1)Manual or semi-automatic dummy bottle

-Plug & play solution

-Maintenance cost reduction

-Replace plastic flexible jaws by metalic gripper with spring

-Redisigned bushing and rod cam

-Reinforced gripper fork

-The new plunger design, significantly lightened, improves the valve performance in the transitory phases of opening and closing. The new geometry of the plunger prevents the deformation of the valve body.

-The innovative eccentric terminal allows filling with a laminar flow, creating less bubbles during filling. Moreover, it allows a precise and clean direction of the product jet, preventing leakages during the filling phases.

-The proposed solution consists of replacing the compressed air drive with a mechanical drive with a spring

-The valve trolley is modified, removing all the seals on the sliding stem and then inserting the new stem and drive spring.

• new gaskets, sliding rings and a slewing ring have been introduced
• the sliding seal has been replaced by a dedicated labyrinth

New Dummy bottle insertion/extraction cam actuated by pneumatic motor.

Rollers and cams desgined to grant less shocks and therefore more reliable system vs. previous one.

• no more metal to metal contact
• increased roller diameter

Easy settings through adjusting screws.

• Internal valve’s components (gaskets, pistons, guiding ring and membranes) are replace with new generation ones
• New components are FDA approved and aromas transfer free

The current solution without torque limiter may lead to costly repairs and machine downtime due to overloads.

The new solution proposes New command with torque limiter and longer shaft

-The automatic lubrication system eliminates the risk of moving parts on the filler which have not been lubricated, thus fully complying with the manufacturer’s instructions.

-The system is managed by the machine PLC which lubricates various points on the machine at preset intervals on the basis of machine rotation time.Manual lubrication can be performed in the event of a PLC fault.

A precisely timed drop of liquid nitrogen is dosed into the headspace above the beverage in a bottle/can after filling and before sealing/capping. The cold liquid nitrogen (-196°C) turns into nitrogen gas at room temperature and expands rapidly. Since the bottle is capped at a certain time after dosing, this process creates a defined internal pressure in the bottle/can.

The Nitrodose system has been developed to meet these requirements and to cut cost at the same time by providing a precise charge of liquid nitrogen.

The current solution enables only manual control of PAA concentration, increasing the risk of contamination of the productThe new solution proposesAutomatic samples of PAA taken from the feed pipingThe titration reading is used to correct the PAA concentration during operation of the filler

-The current solution with valve body and plungers was designed to limit foaming on the neck.

-The new solution improves it even more thanks to a valve body with a smaller outlet to decrease flow deviation

The current solution allow to fill bottles with 38 mm neck finish.The new solution proposes neck 33/12 with new design of grippers to improve stability.

-The purpose is to give customers the possibility to reuse the water used to rinse bottles instead of throwing it away.

-The recovered water can be used as service water (e.g. washing of machines) or reconditioned via active carbon installations. It cannot be reused as process water because the recovered water contains traces of peracetic acid (PAA).